ISSN: 0304-128X ISSN: 2233-9558
Copyright © 2024 KICHE. All rights reserved

Articles & Issues

Language
korean
Conflict of Interest
In relation to this article, we declare that there is no conflict of interest.
Publication history
Received August 21, 2014
Accepted September 17, 2014
articles This is an Open-Access article distributed under the terms of the Creative Commons Attribution Non-Commercial License (http://creativecommons.org/licenses/bync/3.0) which permits unrestricted non-commercial use, distribution, and reproduction in any medium, provided the original work is properly cited.
Copyright © KIChE. All rights reserved.

All issues

산업부산물 구형골재를 사용한 폴리에스테르 폴리머 콘크리트의 특성(II)(플라이 애쉬와 아토마이징 제강 환원슬래그 사용)

Characteristics of Polyester Polymer Concrete Using Spherical Aggregates from Industrial By-Products(II)(Use of Fly Ash and Atomizing Reduction Steel Slag)

공주대학교 화학공학부, 331-717 충남 천안시 부대동 275 1공주대학교 건축학부, 331-717 충남 천안시 부대동 275
Department of Chemical Engineering, Kongju National University, 275 Budae-dong, Cheonan, Chungnam 331-717, Korea 1Department of Architecture, Kongju National University, 275 Budae-dong, Cheonan, Chungnam 331-717, Korea
ehhwang@kongju.ac.kr
Korean Chemical Engineering Research, June 2015, 53(3), 364-371(8), 10.9713/kcer.2015.53.3.364 Epub 2 June 2015
downloadDownload PDF

Abstract

폴리머 콘크리트의 원가절감을 위해서 생산비의 대부분을 차지하는 폴리머 결합재의 사용량을 절감하는 것이 매우 중요하다. 산업부산물로 얻을 수 있는 플라이 애쉬와 아토마이징 제강 환원슬래그는 구형의 재료이다. 구형의 제강환원슬래그는 래들로 환원공정에서 생산되는 제강슬래그를 아토마이징 기술로 제조하였다. 폴리머 콘크리트 복합재료의 제 물성을 조사하기 위하여 폴리머 결합재의 첨가율과 아토마이징 제강 환원슬래그의 대체율에 따라 다양한 배합의 폴리머 콘크리트 공시체를 제조하고 물성시험을 실시하였다. 시험결과, 아토마이징 제강 환원슬래그의 대체율과 폴리머 결합재의 첨가량이 증가됨에 따라 공시체의 압축 및 휨강도는 현저하게 향상되었다. 내열수성시험에서 압 축강도, 휨강도, 밀도 및 세공의 평균직경은 감소되었으나 총세공량과 공극률은 증가되었다. 탄산칼슘(충전재)과 강 모래(잔골재)대신 구형의 플라이 애쉬와 아토마이징 제강 환원슬래그를 사용하여 만든 폴리머 콘크리트의 작업성이 현저히 개선되어 본 연구에서 개발된 폴리머 콘크리트는 종래의 제품보다 폴리머 결합재의 사용량을 18.2% 절감할 수 있게 되었다.
For the cost down of polymer concrete, It is very important to reduce the use amount of polymer binder, which occupies most of the production cost of polymer concrete. Fly ash and atomizing reduction steel slag are spherical materials obtained from industrial by-products. Spherical atomizing reduction steel slag was manufactured using steel slag from reduction process of ladle furnace by atomizing technology. To investigate the physical properties of polymer concrete, polymer concrete specimens were prepared with the various proportions of polymer binder and replacement ratios of atomizing steel slag. Results showed that compressive and flexural strengths of the specimens were remarkably increased with the addition amount of polymer binder and the replacement ratios of atomizing steel slag. In the hot water resistance test, compressive strength, flexural strength, bulk density and average pore diameter decreased but total pore volume and pore diameter increased. We found that polymer concrete developed in this study reduced the amount of polymer binder by 18.2% compared to the conventional product because of the remarkable improvement of workability of polymer concrete using spherical fly ash and atomizing reduction steel slag instead of calcium carbonate (filler) and river sand (fine aggregate).

References

Gorninski JP, Dal Molin DC, Kazmierczak CS, Cem. Concr. Compos., 29, 637 (2007)
Haidar M, Ghorbel E, Toutanji H, Constr. Build. Mater., 25, 1632 (2011)
Fowler DW, Cem. Concr. Compos., 21, 449 (1999)
Czarnecki L, Garbacz A, Kurach J, Cem. Concr. Compos., 23, 399 (2001)
Ohama Y, “Recent Research and Development Trends of Concrete-Polymer Composites in Japan,” Proc. 12th Inter. Cong. on polym. in Conc., September, Chuncheon(2007). (2007)
Gemert DV, Czarnecki L, et al., Cem. Concr. Compos., 27, 926 (2005)
San-Jose JT, Vegas IJ, Frias M, Constr. Build. Mater., 22, 2031 (2008)
Gorninski JP, Dal Molin DC, Kazmierczak CS, Constr. Build. Mater., 21, 546 (2007)
Hwang EH, Kim JM, Appl. Chem. Eng., 25(2), 181 (2014)
Hwang EH, Kim JM, Appl. Chem. Eng., 25(4), 380 (2014)
Bae GB, Lee SG, Yoon HJ, Lee JD, Korean Chem. Eng. Res., 50(3), 588 (2012)
Hwang EH, Kim JM, Yeon JH, J. Appl. Polym. Sci., 129(5), 2905 (2013)
Kim JM, Cho SH, Oh SY, Kwak EG, J. Korea Conc. Instit., 19, 39 (2007)
Hwang EH, Lee CH, Kim JM, Appl. Chem. Eng., 23(2), 210 (2012)
Hwang EH, Lee CH, Kim JM, Appl. Chem. Eng., 23(4), 409 (2012)
Montgomery DG, Wang G, Cem. Concr. Res., 21, 1083 (1991)
Montgomery DG, Wang G, Cem. Concr. Res., 22, 755 (1992)
Oh OS, et al., Patent No. 10-0098062-0000(1996). (1996)
Semerad E, Kremnitzer, Lacom P, Holub WF, Sattler P," Influence of Polymer Addition on Microscopic Properties,” Proc. 5th Inter. Cong. on polym. in Conc., September, Brighton(1987). (1987)

The Korean Institute of Chemical Engineers. F5, 119, Anam-ro, Seongbuk-gu, 233 Spring Street Seoul 02856, South Korea.
Phone No. +82-2-458-3078FAX No. +82-507-804-0669E-mail : kiche@kiche.or.kr

Copyright (C) KICHE.all rights reserved.

- Korean Chemical Engineering Research 상단으로